Scubapro Yoke Nut Socket

1 inch and 26 mm. Use the ratchet and yoke nut socket to remove the yoke nut from the first stage.

Xs Scuba Pro Valve With 1 2 Npt Threads Vx250 22n Vi Leisurepro

This simple tool is a 1.

Scubapro yoke nut socket. Straight Blunt O-Ring Pick. 26 MM Yoke Nut Socket. 3 Remove all hoses.

Remove the cap cover. Thread the first stage handle into the high-pressure port. These tools allow the technician to accurately torque yoke nuts on most first stagesThe sockets are available in two sizes.

Thread the first stage handle into the high-pressure port as shown. Must be employed by an authorized SCUBAPRO facility. 3272009 I used a Craftsman 38th inch drive 1.

1 inch ScubaPro yoke nut wrench. Remove the yoke cover if cleaning the yoke is indicated. The ScubaPro tool again as an example is a specially turned thin wall socket.

Spicer MetricEnglish Nut Washer Nut Torque Socket Axle Models Thread Size Part No. The illustration to the right shows all major com- ponents of the Scubapro Mark 2 first stage as- sembled in cutaway view. 532 For DIN Regulators Remove all hoses.

Socket seem to design their reg so that a specific tool is needed probably to keep people from just using a big crescent wrench on them. Yoke Nut Socket 25 mm for Scubapro First Stage. All SCUBAPRO technicians must be employed by an authorized SCUBAPRO facility.

Huge Selection of Scuba Gear. 10900 Save 1200. Regulators Dive Computers BCDs Fins Dive Wear Snorkels Masks and more.

Yoke end nut application and torque information. 2 TOOLS NEEDED FOR REPAIR OF MK 18 P N 4 3 0 4 0 0 TOOLS NEEDED Quantity Part Number Description 1 Socket Wrench with 38 drive and 3 extension 1 20-155-500 Peter Built 1 Yoke Nut Socket 20270-100 Peter Built Balance Chamber Tool 1 set 10102100 Peter Built Brass oring picks. Thread the first stage handle into the high-pressure port as shown.

After 14 years as the wrench of choice for thousands of Scubapro technicians the Scuba Tools Multi-Tool has proven that it is the right tool for the job. The yoke screw is not. Must be employed by an authorized SCUBAPRO facility.

Driver in from the side to remove the nut. 532 For DIN Regulators Remove all hoses. Thread the first stage handle into the high-pressure port as shown.

Lb-ft Size 15040 STP 19050 STP 19060 SDATP 21060 SDATP M36X15 127589 None 575-703 55mm 22060 SDATP 21080 SDA 22080 SDA 23080 SDA M42X15 128049 None 840-1020 55mm 26080 S. Plus the socket walls are extra thin so it will fit over the Yoke Nut. Be the first to review this product.

Write Your Own Review. Its use is recommended for removal and installation of the yoke nut as opposed to using an adjustable spanner to avoid slipping and damagin. Must be employed by an authorized SCUBAPRO facility.

Use the ratchet and yoke nut socket to remove the yoke nut from the first stage. FREE Shipping for Thailand Orders over 200THB. Comparing mine with a scubapro yoke nut you could probably get away with taking it all the way down to 34th inches high so you do not have to be too accurate.

25mm Yoke Nut Socket Mares 26mm Yoke Nut Socket Aqua Lung 2717mm First Stage Wrench 2mm Slotted Screwdriver 2nd Stage Valve Body Internal Retaining Nut Tool 3. Both sockets are manufactured specifically to fit inside the yoke and over the yoke nut see illustration far right. Socket and the first cut was to reduce its height to 78th inches.

3 Remove all hoses. 2 TOOLS NEEDED FOR REPAIR OF MK 16 P N 4 3 0 4 0 0 TOOLS NEEDED Quantity Part Number Description 1 Socket Wrench with 38 drive and 3 extension 1 20-155-500 Peter Built 1 Yoke Nut Socket 20270-100 Peter Built MK 16 Tool 1 set 10102100 Peter Built Brass oring picks. Wrench is used to tighten or loosen yoke nut once yoke screw has been removedsee photo.

Remove the yoke cover if cleaning the yoke is indicated. ONE RECENT ITEM SHIPPED BY USPS. Deep Down You Want the Best.

SCUBAPRO MK 25MK 20 First Stages Remove all hoses. Yoke Nut Sockets At Scuba Tools we manufacture two custom yoke nut sockets and a custom 38. 7182011 I ask about the yoke nut because some regs like ScubaPro 1.

Must be employed by an authorized SCUBAPRO facility. Drive but its much smaller than any standard available socket. X 38 Drive Extension 332.

1 Yoke Nut Socket. Yoke Nut Socket Kit. Shop the Full SCUBAPRO.

Drive Dial Torque Wrench 0-300 in lbs. And you could leave it at least 14th inch longer and it will still fit OK. Yoke Nut Socket Pete Wolfinger Scubapro Dealer Support.

Ball Point Hex Driver 38. Use the ratchet and yoke nut socket to remove the yoke nut from the first stage. 26 MM Yoke Nut Socket.

SCUBAPRON 2 Full Cutaway Note. It easily slips into the yoke and you can either put a shorty extension down through the yoke screw hole or fit a flat 38. This thin-walled stainless steel 6-point socket is designed to fit the yoke nut of all various first stage regulators such as Oceanic Hollis Aeris Dive Rite just to name a few.

Tool Set For Poseidon Jetstream First Stage Tool Set Poseidon Tools